What're your ideas about Tools You Need to Install a New Bathtub ?
Mounting a bath tub isn't exactly brain surgery, but it does need strong plumbing, woodworking, as well as often, tiling skills. Replacing an old bath tub with a new one is likewise a reasonably difficult job. If the old bathtub is readily easily accessible, the task can move immediately; if you need to open a wall surface to get rid of the old tub as well as place the brand-new bathtub, the job is much harder. In either instance, the job is within a home handyman's abilities, although you will need a helper to vacate the old bathtub and set in the brand-new one. Make sure you have certified on your own for the job as well as fit trying it. Rather than employing a specialist to take over a halfway-completed job, it is much better to take into consideration using one before you begin. Opportunities are you might require a professional plumber to make tube connections.
This short article will assist you set up a brand-new bath tub in your bathroom if you have already purchased a brand-new bathtub and also do not require to alter the plan of your previous water system pipes.
Your tools and product list need to consist of the following:
Preparing for the Installation
Firstly, the supporting frame supplied with the bath should be fitted (if required) according to the manufacturer's instructions. Next, fit the faucets or mixer to the bath tub. When suitable the faucet block, it is necessary to see to it that if the faucet features a plastic washing machine, it is fitted between the bath as well as the taps. On a plastic bath, it is also reasonable to fit a sustaining plate under the faucets system to avoid stress on the bathtub.
Fit the flexible tap adapters to the bottom of both faucets utilizing 2 nuts and olives (sometimes supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and then pass the electrical outlet via the hole in the bathroom. Make use of the nut provided by the supplier to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the adaptable overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which ought to be fitted inside the bath. Make sure you use every one of the provided washing machines.
Link the trap to the bottom of the waste outlet on the bathtub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the trap to the outlet. Connect all-time low of the overflow tube in a comparable manner.The bath ought to now prepare to be suited its final position.
Removing Old Taps
If you require to change old taps with brand-new ones as a part of your setup, then the first thing you need to do is detach the supply of water. After doing so, activate the faucets to drain any kind of water staying in the system. The procedure of eliminating the existing taps can be rather bothersome because of the restricted gain access to that is frequently the instance.
Utilize a basin wrench (crowsfoot spanner) or a faucet tool to undo the nut that attaches the supply pipes to the taps. Have a fabric ready for the staying water that will originate from the pipes. When the supply pipes have actually been removed, utilize the same device to loosen the nut that holds the taps onto the bath/basin. You will certainly need to quit the single faucets from turning throughout this procedure. When the faucets have been gotten rid of, the holes in the bath/basin will need to be cleaned of any type of old securing compound.
Prior to proceeding to fit the new taps, contrast the pipeline connections on the old faucets to the brand-new faucets. If the old taps are longer than the brand-new taps, after that a shank adapter is required for the brand-new faucets to fit.
Installing the Bath tub
Using the two wood boards under its feet, place the tub in the needed placement. The wooden boards are practical in evenly spreading the weight of the bath tub over the location of the boards instead of concentrating all the weight onto 4 small factors.
The following goal is to guarantee that the bath tub is leveled all round. This can be achieved by inspecting the level and adjusting the feet on the bathtub up until the level reviews level.
To set up faucets, fit all-time low of the furthest flexible faucet adapter to the appropriate supply pipe by making a compression join; after that do the very same for the other tap.
Turn on the water system and also examine all joints and new pipework for leaks as well as tighten them if essential. Load the bathtub and likewise inspect the overflow electrical outlet and also the regular outlet for leaks.
Finally, repair the bathroom paneling as defined in the supplier's instruction manual. Tiling and sealing around the tub must wait till the bath tub has actually been utilized a minimum of once as this will settle it right into its last setting.
Suitable New Touches
If the tails of the brand-new faucets are plastic, after that you will certainly require a plastic adapter to stop damages to the string. One end of the adapter fits on the plastic tail of the faucet and also the various other end gives a link to the current supply pipelines.
If you require to fit a monobloc, after that you will certainly need minimizing couplers, which attaches the 10mm pipeline of the monobloc to the common 15mm supply pipeline.
Next off, place the tap in the installing hole in the bath/basin guaranteeing that the washers are in place between the faucet and also the sink. Safeguard the faucet in position with the maker offered backnut. When the tap is securely in position, the supply pipelines can be attached to the tails of the faucets. The taps can either be connected by using corrugated copper piping or with regular faucet ports. The former type should be attached to the faucet finishes first, tightening just by hand. The supply pipelines can later on be linked to the other end. Tighten up both ends with a spanner after both ends have actually been linked.
Tiling Around the Bathtub
In the area where the bathroom satisfies the ceramic tile, it is required to seal the accompanies a silicone rubber caulking. This is very important as the installation can relocate enough to crack an inflexible seal, creating the water to permeate the wall in between the bathroom and the tiling, leading to difficulties with moisture and feasible leakages to the ceiling below.
You can choose from a selection of coloured sealants to blend in your components as well as installations. They are offered in tubes and cartridges, and also can sealing voids as much as a width of 3mm (1/8 inch). If you have a bigger space to load, you can load it with twists of drenched paper or soft rope. Remember to always load the bathtub with water prior to sealing, to enable the movement experienced when the bathtub is in usage. The sealant can crack relatively early if you do not think about this movement prior to sealing.
Conversely, ceramic coving or quadrant ceramic tiles can be made use of to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as reduce to size, are additionally quickly available on the marketplace. It is advisable to fit the ceramic tiles using waterproof or waterproof sticky and also grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I came across that review about How to Install a Bathtub while doing a search on the internet. Sharing is caring. Who knows, you might be helping someone out. Thanks a lot for your time spent reading it.
Book A Service Call